CR-453CS

Rotary Tool Buffing Wheel 15/16" MC13 180 grit Scotch BriteTM abrasive.Check out the photos... You don't want to rebuild without...

Rotary Tool Buffing Wheel 15/16" MC13 240 grit Scotch BriteTM abrasive.Check out the photos... You don't want to rebuild without...

CARBON FIBER DRAG WASHER SET F0R CONTOURA CR-303CS & 453CS REELS BY DRAGMASTERSTM Drastically increase the performance potential of any Okuma Contoura CR-303CS & 453CS reel in only minutes by...

Decorate your Boat, Truck, Car, Laptop, or whatever else you can think of with this official DRAGMASTERSTM 4" wide by 3" high long-life vinyl decal. This sticker is of a high quality, U.V resistant, water resistant,...

Decorate your Boat, Truck, Car, Laptop, or whatever else you can think of with this official DRAGMASTERSTM 8.5" wide by 3.75" high long-life vinyl decal. This sticker is of a high quality, U.V resistant, water resistant,...

OKUMA 0.35 OZ. REEL OIL

OKUMA CAST CONTROL CAP KIT The best way to go to take all the guess work out of missing parts & way cheaper too! This complete Okuma Cast Control Cap Kit uses only genuine Okuma O.E.M. parts to ensure a complete...

OKUMA ROD BRACE CLAMP & HARDWARE KIT Our kits are the best way to go that are designed to take all the guess work out of missing parts & way cheaper too! This complete Okuma Rod Brace Clamp &...

OKUMA HANDLE INSTALLATION KIT Our kits are the best way to go that are designed to take all the guess work out of missing parts & way cheaper too! This complete Okuma Handle Installation Kit uses only genuine...

OKUMA 11140037 ROD BRACE CLAMP This Brace itself will fit reel seats with mounting hole dimensions from @ 1 1/4" to 1 3/8" (@ 32mm to 35mm) and does not include any hardware. If you need the complete kit with...

OKUMA 11150003 ROD BRACE CLAMP BOLT FLAT HEAD

OKUMA 11150003 ROD BRACE CLAMP BOLT ROUND HEAD

OKUMA 11160003 ROD BRACE CLAMP NUT LONG (1...

OKUMA 11160003 ROD BRACE CLAMP NUT SHORT...

OKUMA 11170002 ROD BRACE CLAMP NUT

OKUMA 11170011 HANDLE RETAINER NUT *Handle Retainer Nut numbers 11170011, 11170017, & 11117007-03001 are all the same part, just assigned a different production number. Click here for our complete Handle...

OKUMA 12010037 ANTI REVERSE PAWL...

OKUMA 12070083 HOLD PLATE (11207049-01001) CATALINA CT-455Da, 45C, 45D, & 45L CLARION CLR-453L, 453LS, & 454D CONTOURA CR-453CS CONVECTOR CV-45C, 45D, 45DS, 45L, & 45LS MAG SYSTEM MG-45CS &...

OKUMA 12110012 ANTI REVERSE PAWL PIN (11211005-03002)

OKUMA 12150013 HOLD PLATE BUSHING *Bushing numbers 12150013, 12150015 11215009-03001, & 11215011-03001 are all the same part that were just assigned a different production number over the years...

OKUMA 12160006 CLICK PAWL...

OKUMA 13000958 VICE SIDE PLATE CLARION CLR-453L & 453LS CONTOURA...

OKUMA 13020002 WASHER (11302002-03001) This is the metal end thrust washer that resides behind or under the ball bearing or bronze bushing located on the click side or vice  side plate...

OKUMA 13020025 WASHER...

OKUMA 13030052 CLICK BUTTON...

OKUMA 13040011 CLICK PAWL (1130401301)

OKUMA 13040013 CLICK...

OKUMA 13050009 CLICK PAWL SPRING (1130500301) CATALINA CT-305Da & 455Da CEDROS CSD-10, 10S, 12, 12S, & 15S CLARION CLR-303L, 304D, 453L, 453LS, & 454D CONTOURA CR-303CS & 453CS CORTEZ CZ-10CS,...

OKUMA 14010026 SPOOL CLICK GEAR  *Spool Click Gear numbers 14010026, 1140101101, & 11401001-05002 are all the same part that were just assigned a different production number over the years...

OKUMA 14010029 CLICK GEAR CLARION CLR-453L & 453LS CONTOURA CR-453CS MAG SYSTEM MS-45CS & 45LS MAGNETICS MG-45CS &...

OKUMA 14010030 STAR DRAG CLICK GEAR...

OKUMA 15150001 HANDLE NUT LOCK SCREW *Screw number 15150001, 15150002, 11515001-03907, & 11515001-06001 are all the same part that was just assigned a different production number...

OKUMA DRAG SPRING WASHER PAIR *Drag Spring Washer numbers 16090002, 16090003, 16090004, 16090009, 11609003-05907,11609003-06001, 11609003-06002, & 11609003-06003 are all the same part that were just assigned a...

OKUMA 16110045 EARED WASHER...

OKUMA 16120032 KEY WASHER (11612012-06002)

OKUMA 16120035 KEY WASHER (11612015-06001)

OKUMA 16140003 DRAG SPRING WASHER This is the Spring Washer that prevents any binding issues between the Star Drag Knob & the Handle arm itself. *Washer numbers 16140001, 16140003, 11614001-06,...

OKUMA 16150156 INDEXED STAR DRAG KNOB ASSEMBLY (1161501702927) CLARION CLR-303L, 453L, & 453LS CONTOURA CR-303CS &...

OKUMA 16180002 WASHER (1161800201) This is the black rubber spacer that resides between the inside of the Cast Control Cap & the metal End Thrust Washer. We also include this in our Cast Control Kits...

OKUMA 17000234 BRASS DRIVE GEAR 6.2:1 *Drive Gear numbers 17000234, 17000236, 17000237, & 1170002606002 are all the same part that were either assigned a different production number or have been replaced by...

OKUMA 17010144  DRIVE GEAR SHAFT Drive Gear Shaft numbers 17010142, 17010144, 17010146, 1170103406001, & 1170103416001 are all the same part that were just assigned a different production number that has an...

OKUMA 17020272 PINION GEAR 6.2:1 *Pinion Gear numbers 17020272, 17020275, 17020276, 17020485, 1170203203002, & 1170203206002 are all the same part that were either assigned a different production number...

OKUMA 17020272 STAINLESS STEEL PINION GEAR 6.2:1 *Pinion Gear numbers 17020272, 17020275, 17020276, 17020485, 1170203203002, & 1170203206002 are all the same part that were either assigned a different...

OKUMA 17040025 LINE GUIDE SUPPORT BAR...

OKUMA 17200006 DRIVE GEAR SHAFT BUSHING (11720006-06001) *This Drive Gear Shaft Bushing has an overall length of .563" (@ 9/16" or 14...

OKUMA 18000015 CLUTCH CAM (11800004-12003)

OKUMA 18010012 CLUTCH SPRING (11801009-06001)

OKUMA 18020106 CLUTCH BAR ASSEMBLY (1180201304927) CLARION CLR-453L, 453LS, 454D, 553L, & 553LS CONTOURA CR-453CS, 553, &...

OKUMA 18040008 CLUTCH CAM SLIDER (011804008-06001) CATALINA CT-25C, 25CS, 25D, 25L, 30C, 30CS, 30D, 30L, 45C, 45D, 45L, 305Da, & 455Da CEDROS CSD-10S & 12S CLARION CLR-303L, 304D, 453L, 453LS, &...

OKUMA 18050003 PINION GEAR YOKE If you are intending to use this part on any reel other than a 55, 553, or 603 size reel, please click here instead. The number that is shown on most of the parts diagrams is incorrect &...

OKUMA 18060001 YOKE SPRING 1 PAIR *Yoke Spring numbers 18060001, 18060002, 18060003, 11806001-06, & 11806001-061 are all the same part that were just assigned a different production number. **Even though...

OKUMA 0910012 BALL BEARING Ball Bearing numbers 0910012, 09100226, 0910227, 0910228, 0910229, 0910350, 01041104-61, 01041104-601, 01041104-611, & 01041104-615 are all the same part that were just...

OKUMA 0910026 BALL BEARING This Ball Bearing may arrive in either a sealed or unsealed configuration as shown in the photos. *Ball Bearing numbers 0910026, 0910248, 0910249, 0910250, 0910251, 0910349, 01061335-6,...

OKUMA 0910080 ONE WAY BALL BEARING *Ball Bearing numbers  0910080, 0910152, 0910153, 0110160901, 01101609-6, & 01101609-61 are all the same part that were just assigned a different production number. The depth of...

OKUMA 0920085 CLICK BUTTON WASHER *Washer numbers 0920085, 0920370, 024.05x10x0.2-8, & 024.05x10x0.3-8 are all the same part that were just assigned a different production number over the years. This is the small clear...

OKUMA 0920114 DRIVE GEAR SHAFT WASHER Washer numbers 0920114, 0920284, 025.1x10.5x0.2-6, & 025.1x9.5x0.2-6 are all the same part that were just assigned a different production number. This is the silver colored...

OKUMA 0920133 CLEAR HANDLE WASHER (026x13x0...

OKUMA 0920373 WASHER (023x8x0...

OKUMA 0920435 WASHER (025.1x11.5x0...

OKUMA 0930194 CLUTCH CAM SLIDER & CLICK BUTTON SCREW *Screw numbers 0930194, 0930195, 0930609, 03312X5-617 & 03312X3.5-61 are all the same part that were just assigned a different production number...

OKUMA 0930196 CLICK BUTTON SCREW (03312x5-61) This is the Screw that secures the Click pawl to the Click Button & is included in all our Clicker Repair kits. If you intend to use this screw or if your schematics...

OKUMA 0930202 DRIVE GEAR SHAFT SCREW (03319.4x3x7-61) This is the screw that secures the Drive Gear Shaft (#701) to the Hold Plate (#207). This Drive Gear Shaft Screw will work on all right hand retrieve conventional star...

OKUMA 0930501 SPOOL CLICK GEAR SCREW (03212x5-617) This is the small screw that attaches the Spool Click Gear to the actual Spool itself. Two are required...

OKUMA 0930585 SCREW (03723x11.5-61) This is the Screw that secures the Handle Side Plate to the Main Body Assembly...

OKUMA 12210001 "O" RING This is the 'O' ring that is seated at the base of the threaded brass boss on the main drive side plate for the cast control knob & now included in our Cast Control Kits. This is also the...

OKUMA 29000006 'C' RETAINER (12900006-06001) This 'C' Retainer is used on each side of either the Ball Bearing or on the outside of the white Bushing that is located on the drive side of the spool. On 55 or...

EXCLUSIVELY USED BY TUNA'S REEL TROUBLES AND DRAGMASTERS!    MADE IN USA This listing is for one cup of grease containing at least 1.5 oz. that we use as a great metal to metal lubricant that helps to aid in...