MS-15LS

DAIWA HB-1 PRECISION REEL OILER 64110100

EXCLUSIVELY USED BY TUNA'S REEL TROUBLES!    MADE IN USA This listing is for one cup of grease containing at least 1.5 oz. that we use as a great metal to metal lubricant that helps to aid in preventing...

Rotary Tool Buffing Wheel 15/16" MC13 180 grit Scotch BriteTM abrasive.Check out the photos... You don't want to rebuild without...

OKUMA 0.25 OZ. REEL OIL

OKUMA CAST CONTROL CAP KIT The best way to go to take all the guess work out of missing parts & way cheaper too! This complete Okuma Cast Control Cap Kit uses only genuine Okuma O.E.M. parts to ensure a complete...

OKUMA 17150009 LINE GUIDE PAWL If you need a Line Guide Pawl for any Okuma 15, 20, 25, 30, or 45 Size level wind reel, this O.E.M. part is it & If your unsure, just check out the list below! Line...

OKUMA ROD BRACE CLAMP & HARDWARE KIT Our kits are the best way to go that are designed to take all the guess work out of missing parts & way cheaper too! This complete Okuma Rod Brace Clamp &...

OKUMA 11050006 (11105003-01) WORM SHAFT BUSHING *Please note that this worm shaft bushing may arrive in either black or white molded plastic & is used for the either end of the worm shield...

OKUMA 11150003 ROD BRACE CLAMP BOLT FLAT HEAD

OKUMA 11150003 ROD BRACE CLAMP BOLT ROUND HEAD

OKUMA 11160003 ROD BRACE CLAMP NUT SHORT...

OKUMA 11160003 ROD BRACE CLAMP NUT LONG (1...

OKUMA 11050007 (11105004-01) WORM SHAFT BUSHING *Please note that this worm shaft bushing may arrive in either black or white molded plastic & is used for the "notched " end of the worm shield...

OKUMA HANDLE INSTALLATION KIT Our kits are the best way to go that are designed to take all the guess work out of missing parts & way cheaper too! This complete Okuma Handle Installation Kit uses only genuine...

OKUMA 11170002 ROD BRACE CLAMP NUT

OKUMA 11170011 HANDLE RETAINER NUT *Handle Retainer Nut numbers 11170011, 11170017, & 11117007-03001 are all the same part, just assigned a different production number. Click here for our complete Handle...

OKUMA 12010020 ANTI REVERSE PAWL (11201014-06001) CATALINA CT-15D, 15L, 20C, 20CS, 20D, & 20L CONVECTOR CV-15D, 15L, 20C, 20CS, 20D, & 20L MAGNETICS MG-15CS, 15LS, 20CS, & 20LS MAG SYSTEM MS-15CS, 15LS,...

OKUMA 29010001 WASHER...

OKUMA 12150013 HOLD PLATE BUSHING *Bushing numbers 12150013, 12150015 11215009-03001, & 11215011-03001 are all the same part that were just assigned a different production number over the years...

OKUMA 12240004 & 12240017 ONE WAY BEARING CUP...

OKUMA 12110002 ANTI REVERSE PAWL PIN *Part numbers 12110002, 12110006, 12110008, 11211002-03001, 11211002-03, & 11211005-03001 are all the same part that were just assigned a different production...

OKUMA 14180001 SPOOL BEARING FIXED PLATE (11418001-01001) CATALINA CT-15C, 15D, 15L, 20C, 20D, & 20L CONVECTOR CV-15C, 15CS, 15D, 15L, 20C, 20CS, 20D, 20DLX, &...

OKUMA 16040002 DRAG / CONTROL CLICK *Control Click numbers 16040002, 16040003, 1604002-01001, & 1604003-01001 are all the same part, that were just assigned a different production number. CATALINA CT-15C, 15D,...

OKUMA 15130015 HANDLE COVER * Handle Cover numbers 15130015, 15130017, & 11513010-01001 are all the same part, that were just assigned a different production number. CATALINA (First Generation) CT-15C, 15D, 15L,...

OKUMA 12160004 ANTI-RE PAWL SPRING *Spring numbers 12160004, 11216001-06, & 11216001-06002 are all the same part that were just assigned a different production number. CATALINA CT-15C, 15D, 15L, 20C,...

OKUMA 13020017 CAST CONTROL END THRUST WASHER *Washer numbers 13020017, 13020018, 11302006-3, & 11302006-3001 are all the same part that were just assigned a different production number & is...

OKUMA 13020014 WASHER / SPACER *Spacer numbers 13020014, 13020015, 11302002-03, 11302002-06001, & 11302002-03002 are all the same part that were just assigned a different production number that may arrive in...

OKUMA 13030053 CLICK BUTTON MAG SURF ALC-20CS MAG SYSTEM MS-15CS, 15LS, 20CS, &...

OKUMA 13040011 CLICK PAWL (1130401301) CLARION CLR-203L, 303L, 453L, & 453LS CONTOURA CR-203CS. 303CS, & 453CS CORTEZ CZ-5CS, 5CSa, 10CS, 10CSa, 12CS, & 12CSa MAGNETIX  MG-15CS,...

OKUMA 13040013 CLICK PAWL (1130401201) CATALINA CT-305Da CLARION CLR303L, 304D, 453L, 453LS, & 454D CONTOURA CR-303CS & 453CS MAGNETICS MG-30CS, 30LS, 45CS, & 45LS MAG SYSTEM MS-15CS, 15LS, 20CS, 20LS,...

OKUMA 13040012 CLICK PAWL SPRING (11304009-06001) CATALINA CT-15C, 15D, 15L, 20C, 20D, 25C, 25CS, 25D, 25L, 30C, 30CS, 30D, 30L, 45C, 45D, 45L, 55C, 55N, & 55W CHROMER CR-250, 250LX, 400, & 400LX FINA Fi-150,...

13050010 CLICK  PAWL SPRING (1130500401)

OKUMA 14010026 SPOOL CLICK GEAR  *Spool Click Gear numbers 14010026, 1140101101, & 11401001-05002 are all the same part that were just assigned a different production number over the years. *Please...

OKUMA 15150001 HANDLE NUT LOCK SCREW *Screw number 15150001, 15150002, 11515001-03907, & 11515001-06001 are all the same part that was just assigned a different production number. CATALINA CT-15C, 15D,...

OKUMA DRAG SPRING WASHER SET *Drag Spring Washer numbers 16090002, 16090003, 16090004, 16090009, 11609003-05907,11609003-06001, 11609003-06002, & 11609003-06003 are all the same part that were just assigned a...

OKUMA 18150001 SCREW This is the Screw that secures the Clutch Bar to the Clutch Cam. *Screw numbers 18150001, 18150002 & 11815001-16001 are all the same part that were just assigned a different number over...

OKUMA 16120047 KEY WASHER (11612029-06001) This is the washer that resides on the Drive Shaft between the Handle Assembly & the black plastic Drag Click. This Key Washer is identified as Key...

OKUMA 16180002 WASHER (1161800201) This is the black rubber spacer that resides between the inside of the Cast Control Cap & the metal End Thrust Washer. We also include this in our Cast Control Kits...

OKUMA 17010181 DRIVE GEAR SHAFT (1170104416001) This Drive Gear Shaft has an overall length of @ 2.126" (54mm). CATALINA (1ST GEN.) CT-15C, 15D, 15L, 20C, 20D, & 20L CORTEZ CZ-5CS & 5CSa MAG SYSTEM...

OKUMA 17030011 WORM SHAFT GUARD (11703011-03001) CATALINA CT-15D & 15L CLASSIC PRO CLX (XT) CLX-150La COLD WATER CW-153D CONVECTOR CN / CV-15D & 15L MAGDA PRO MA-15D, 15DT, 15DX, & 15DXT MAGNETIX...

OKUMA 17040024 & 17040042 LINE GUIDE SUPPORT BAR (11704015-03001) CATALINA CT-15D & 15L CLASSIC PRO CLX (XT) CLX-150La COLD WATER CW-153D CONVECTOR CN-15D & 15L MAG SYSTEM MS-15LS STRATAMASTER...

OKUMA 17050011 WORM SHAFT TRANSMISSION GEAR (11705006-06) This is the steel Transmission Gear that resides on the end of the Worm Shaft that is located on the Clicker side of the reel. This is also referred to as the...

OKUMA 17060003 TRANSMISSION GEAR (11706002-06) *This is the small Transmission Gear that resides on the end of the spool shaft on the clicker side of the reel. This Gear may arrive in either a cast steel or brass finish...

OKUMA 17070009 TRANSMISSION GEAR (11707008-11) This is the "stepped" Transmission Gear that is located under the Click Pawl Spring that is secured to the Vice Side Plate with one small Phillips screw & is also referred...

OKUMA 17090004 & 17090017 TRANSMISSION GEAR BUSHING *This is the brass bushing that resides on the vice side plate ("click side, side cover") that helps reinforce the post that the transmission gear is secured to...

OKUMA 17100044 LINE GUIDE (1171001206917) CATALINA CT-15D & 15L CLARION CLR-203L & 204D CLASSIC PRO XPD-20D COLD WATER CW-153D, 153DLX, 153DLXm, CW-203D, 203DLX, & 203DLXm COLD WATER LADIES EDITION...

OKUMA 17120052 WORM SHAFT MAG SYSTEM MS-15LS MAGNETICS...

OKUMA 17130001 LINE GUIDE PAWL CAP Pawl Cap numbers 17130001, 17130002, & 11713001-03907 are all the same part that were assigned a different production number...

OKUMA 18000014 CLUTCH CAM / CLUTCH SHAFT Clutch Cam numbers 18000012, 18000014, 11800004-02002, & 11800004-12002 are all the same part, that were just assigned a different production number. AVENGER...

OKUMA 18010008 CLUTCH SPRING (11801006-06001) *Please examine the spring you are replacing closely & compare it to the one in the photographs as there has been a design change, If the spring you are replacing...

OKUMA 18020078 CLUTCH BAR ASSEMBLY (1180201106001) CATALINA CT-15C, 15D, 15L, 20C, 20D, & 20L MAG SYSTEM MS-15CS, 15LS, 20CS, &...

OKUMA 18040009 CLUTCH CAM SLIDER (11804009-06001) ALC-MAG ALC-20CS CATALINA CT-15C, 15D, 15L, 20C, 20D, & 20L CLARION CLR-203L & 204D COLD WATER CW-153D & 203D CONTOURA CR-203CS  CONVECTOR CV-15C,...

OKUMA 18050005 PINION GEAR YOKE (11805005-06001) CATALINA CT-15C, 15D, 15L, 20C, 20D, & 20L CLARION CLR-203L & 204D COLD WATER CW-153D, 153DLX, 153DLXm, 203D, 203DLX, &...

OKUMA 18060004 YOKE SPRING (1180600102) 1 PAIR

OKUMA 29000001 E RETAINER...

OKUMA 29000006 'C' RETAINER (12900006-06001)

OKUMA 19010001 'C' RETAINER (11901001-06) On Conventional Reels: This 'C' Retainer is used on the clicker side of the spool shaft that secures either the brass, steel or white plastic Transmission Gear (#706) in...

OKUMA 0910080 ONE WAY BALL BEARING *Ball Bearing numbers  0910080, 0910152, 0910153, 0110160901, 01101609-6, & 01101609-61 are all the same part that were just assigned a different production number. The depth of...

OKUMA 0930480 SIDE PLATE SCREW (03712...

Decorate your Boat, Truck, Car, Laptop, or whatever else you can think of with this official DRAGMASTERS  8.5" wide by 3.75" high long-life vinyl decal. This sticker is of a high quality, U.V resistant, water resistant,...

Decorate your Boat, Truck, Car, Laptop, or whatever else you can think of with this official DRAGMASTERS 4" wide by 3" high long-life vinyl decal. This sticker is of a high quality, U.V resistant, water resistant,...

OKUMA 0920186 TRANSMISSION GEAR WASHER (025.1x10.5x5-6) This is the washer that is located on the clicker side of the spool that resides between the small transmission gear & the spool click gear itself...

OKUMA 0930171 SCREW (03222.6X4.5-61) On conventional star drag reels this screw is used to secure the one way bearing cup to the handle side plate. On spinning reels this screw is used to secure the transmission gear...

OKUMA 0930210 TRANSMISSION GEAR SCREW (11707008-11) This is the Screw that Secures the white or black plastic Transmission Gear #707 to the Vice Side plate...

OKUMA 0920282 WORM SHAFT WASHER (025.1x8x0.2-6) *This is the Washer that generally resides on the Worm Shaft between the Worm Shaft Bushing & 'E' Clip on the Handl side of the reel...

OKUMA 0920162 WASHER (028x10x0...

OKUMA 0920111 WASHER (025.1x11.5x.5-6) This is the Washer that generally resides between the Drive Gear Shaft Screw #0930202 & the Hold Plate Bushing...

OKUMA 0920373 WASHER (023x8x0...

OKUMA 0930566 SCREW (03222...

OKUMA 0930501 SPOOL CLICK GEAR SCREW (03212x5-617) This is the small screw that attaches the Spool Click Gear to the actual Spool itself. Two are required...

OKUMA 0930928 SCREW...

OKUMA 0930651 SCREW (03327.5x2.6x7.5-61) This is the Screw that secures the white or black Transmission Gear to the Vice side Plate (Clicker Side Plate) & in some applications helps secure the Hold Plate to the...

OKUMA 0930549 VICE SIDE PLATE SCREW (03222...

OKUMA 0930176 SCREW (03222.6x9...

OKUMA 0920114 DRIVE GEAR SHAFT WASHER Washer numbers 0920114, 0920284, 025.1x10.5x0.2-6, & 025.1x9.5x0.2-6 are all the same part that were just assigned a different production number. This is the silver colored...

OKUMA 0930673 SCREW (03327x2.6x4-61) On conventional star drag reels this screw is used to secure the spool bearing fixed plate to the main body & on spinning reels this is used as a rotor nut lock screw...

OKUMA 0910026 BALL BEARING *Ball Bearing numbers 0910026, 0910248, 0910249, 0910250, 0910251, 0910349, 01061335-6, 01061335-6, 01061335-601, 01061335-611, 01061335-612, & 01061335-615 are all the same part...

OKUMA 0910096 BALL BEARING (01081605-61) *Ball Bearing numbers 0910096, 0910097,  0910099, 0910103, 0910104, 0910280, 0910327, 0910365, 01081605-5, 01081605-6, 01081605-51, 01081605-511, 01081605-61,...

OKUMA 0930194 CLUTCH CAM SLIDER & CLICK BUTTON SCREW *Screw numbers 0930194, 0930195, 0930609, 03312X5-617 & 03312X3.5-61 are all the same part that were just assigned a different production number...

OKUMA 0920066 & 6K148801 LINE GUIDE PAWL WASHER (022X4.9X0.2-3) This is the small brass or silver washer (or shim) that resides inside the Pawl Cap on all level wind equipped reels & is also referred to as the...

OKUMA 0910012 BALL BEARING Ball Bearing numbers 0910012, 09100226, 0910227, 0910228, 0910229, 0910350, 01041104-61, 01041104-601, 01041104-611, & 01041104-615 are all the same part that were just...

OKUMA 0920133 CLEAR HANDLE WASHER (026x13x0...

OKUMA 0920085 CLICK BUTTON WASHER *Washer numbers 0920085, 0920370, 024.05x10x0.2-8, & 024.05x10x0.3-8 are all the same part that were just assigned a different production number over the years. This is the small clear...

OKUMA 0930196 CLICK BUTTON SCREW (03312x5-61) This is the Screw that secures the Click pawl to the Click Button. If you intend to use this screw or if your schematics call for use of this screw as a Slider Screw, your...

OKUMA 0930202 DRIVE GEAR SHAFT SCREW (03319.4x3x7-61) This is the screw that secures the Drive Gear Shaft (#701) to the Hold Plate (#207). This Drive Gear Shaft Screw will work on all right hand retrieve conventional star...

OKUMA 12210001 "O" RING This is the 'O' ring that is seated at the base of the threaded brass boss on the main drive side plate for the cast control knob. This is also the same part as 0940025, 061.5x7-0701, &...

OKUMA 46010002 COMPRESSION SPRING (14601001-16) CATALINA CT-15C, 15D, 15L, 20C, 20D, 25C, 25CS, 25D, 25L, 30C, 30CS, 30D, 30L, 45C, 45D, 45L, 55C, 55N, & 55W CHROMER CR-250, 250LX, 400, &...